-
Thanks for the suggestion on setting up a member ride thread. I'll do that.Rick88ss wrote:
Woah!
That Z looks super clean. Post up more pics and put up a member ride thread.
Still looking for thoughts on a finding a chrome hub… you can see the driver side rear is missing one. -
I don't know who's Z31 this is but this the wheels I'm rockin.
Staggered Z32TT wheels 1.25 front and 1.5 inch spacer rear dropped on STsprings.Cha iro
enjoy building it yourself.
if it fails, fuck it.
at least you gave it a whirl. -
my 300zr 18x10+12 & 18x11+20 255/35 & 285/30
84 zenki 19x8.5+18 & 19x9.5+13 235/35 & 265/30
jon.87 300zr vg30de as standard, 88 200zr with rb30et, 84 zenki 200zr replica build with rb25det -
Need more pictures of this car. Im digging it.rbz31 wrote: my 300zr 18x10+12 & 18x11+20 255/35 & 285/30
jon.86na - BlueZ
Shiro #366 - Kouki Monster
85t - Mr Tickles -
XXR 521 18x10 +12 all around
still need to put the 10mm spacer on the rear, roll and possibly pull in the rear. Front just needs more low
Edit: Suspension setup in rear is s13, with stance coils and SPL control arms
Front setup is just stance coils with the camber plates at the top1uz Swapped, lowered, flaked out '86 z31
'72 Datsun 510 4dr, ka24de-T, slammed resto mod
'84 z31 turbo, coils, wheels a.k.a the gfs weekend car
'86 na2t parts for now a.k.a eventually will get running with a/c daily
'83 280zx project backburner a.k.a ls turbo drag car one day
Custom vg30et tube chassis drift exocet project -
Should mention your suspension setup too, cause on z31 rear suspension that'll sit differently.
1988 300zxt. gt35, stance, etc. Wheels: Varrstoen ES2 18x9.5 et-13 225/40. 18x10.5 et0 245/40
1990 jetta vr6'd -
done!DeleriousZ wrote: Should mention your suspension setup too, cause on z31 rear suspension that'll sit differently.1uz Swapped, lowered, flaked out '86 z31
'72 Datsun 510 4dr, ka24de-T, slammed resto mod
'84 z31 turbo, coils, wheels a.k.a the gfs weekend car
'86 na2t parts for now a.k.a eventually will get running with a/c daily
'83 280zx project backburner a.k.a ls turbo drag car one day
Custom vg30et tube chassis drift exocet project -
Post the pictures and information into this thread, its much more relevant. I am not sure why this one was even stickied.
viewtopic.php?f=2&t=17576&hilit=wheel86na - BlueZ
Shiro #366 - Kouki Monster
85t - Mr Tickles -
will do1uz Swapped, lowered, flaked out '86 z31
'72 Datsun 510 4dr, ka24de-T, slammed resto mod
'84 z31 turbo, coils, wheels a.k.a the gfs weekend car
'86 na2t parts for now a.k.a eventually will get running with a/c daily
'83 280zx project backburner a.k.a ls turbo drag car one day
Custom vg30et tube chassis drift exocet project -
1988 300ZX Turbo, Shiro Special #760
1988 300ZX Turbo Automatic (wife's car)
1991 Hard-body 2WD
http://zccw.org/zccw/?page_id=1215 -
Using oem 350z tire specs the 350z Anniversary wheels with +30 offset up front and +33 in the rear will not clear the strut and the center caps wont fit, the tire will still turn but you will see that its rubbing against the strut. However you choose to do it is up to you but you WILL need to space the wheels. Given the wheel still turns the space is very minimal so keep that in mind. You will also need open ended lug nuts if you go with the hubcentric route I chose.
I absolutely reccomend hubcentric adapters over sketchy wheel spacers.
What I used:
Hubcentric wheel adapters that are 1 1/2" thick with 5x114.3 to 5x114.3 and a set of open ended lug nuts. Here are some pictures of the adapters and fitment on stock suspension.
-
Got my V8 swap up and running (well) and threw these on the car
Volk LE37
18x8.5/9.5 +22
245/40 fronts and 275/40 rears
-
Is there a new wheel show? All the links on here and my old ones are all dead.... Need new wheels this year.Who needs new car's, Nissan had it right 30 years ago!!! -
86na - BlueZ
Shiro #366 - Kouki Monster
85t - Mr Tickles -
ThanksWho needs new car's, Nissan had it right 30 years ago!!!
Copyright © 2006–. All rights reserved. Privacy Policy